Cutlass 442 Carburetors. For the first time ever we are offering a restoration service for your Quadrajet carburetor. The carburetor you send us will be the one you get back. All of the carbs restored by us are completely disassembled, then ultrasonically cleaned. The castings are then inspected. Mildly warped air horns and bases are replaned to insure straightness and a perfect seal to the throttle body. All parts are then replated or dichromated as original. This helps to prevent oxidation and corrosion of the castings. Zinc plating and yellow cadmium plating is used on all parts where original. All of the throttle bodies and air horns are dichromated, as original, which returns these components to their original color. This process also seals and protects these vital parts from corrosion on the outside and fuel oxidation on the internal components insuring you a carburetor that will be good for another 50 years, not just until the fuel starts stripping off the spray paint. NOTHING on these rebuilds is painted. All components are finished just as they were when Rochester supplied it new.
All of the plating and dichromating is done in house. When you get your unit back it will look just like it did when it was new. I am not aware of any other carburetor builder in the U.S. that can make these claims. If they do any plating at all they do the zinc and cadmium plating then “paint” the outside of throttle body and air horn.
All throttle shafts are removed and bronze bushings are installed to prevent vacuum leaks and insure idle quality.
All carbs are returned with a new fuel filter installed. If you have a stripped or nearly stripped fuel inlet, we can repair that for you.
All units are engine tested on fuel, solvent rinsed and air dried before being returned. All have a 90 day warranty. Please note: We can not promise that your car can “pass smog” after a rebuild as we have no way to test for this.
All gaskets and seals are also replaced and new mounting gaskets and air cleaner to carburetor gaskets are supplied. All accelerator pumps and are replaced with modern Viton rubber seals that will stand up to today’s modern alcohol blend fuels. All fuel wells are sealed and the throttle plates are micro sealed with Dag Blend 13 to improve idle quality.
All carbs have the following adjustments made on the test stand:
Float level adjustment
Accelerator Pump adjustment
Choke Coil Lever adjustment
Fast Idle Cam adjustment
Air Valve Dashpot adjustment
Choke Coil adjustment
Vacuum Break adjustment
Air Valve Lockout adjustment
Secondary Opening adjustment
Air Valve Spring adjustment
Slow Idle adjustment
Fast Idle adjustment
Secondary Closing adjustment
In most cases you will be able to bolt the unit back on your car and drive it with minimal or no adjustments.
Price is $489, plus shipping. 90 day warranty from the day you install it applies. Be sure to use an inline fuel filter if you are not sure of the status of your fuel tank as we will not warranty repair carbs full of dirt or rust from a polluted tank.
Send your carb (insured) and contact information to:
14100 Wingfoot Crt
Basehor KS, 66007
Please allow 3 – 4 weeks time for this service.
If you have any questions about this service or any part that we sell contact us at 913-304-1792 for more info.
- Category: Carburetors
Showing all 10 results
Quadrajet Carburetor 7027036$689.00 Add to cart
Throttle Accelerator Return Spring$5.00 Add to cart
End Carburetor Top Plate, Tri Power$89.00 Add to cart
1966 Tri-Power Carburetors, Set of 3.$1,296.00 Read more
Carburetor Base Plate, Tri-Power$79.00 Add to cart
Carburetor Mounting Gasket$12.00 Add to cart
Fuel Filter 1976-77 4 Barrel$5.00 Add to cart
Fuel Filter 1968-75 4 Barrel$5.00 Add to cart
Fuel Filter 1967 4 Barrel$5.00 Add to cart
Fuel Filter / Vapor Diverter 1971-1972 W30$49.00 Add to cart